Kinetic of CO2 absorption and carbamate formation in aqueous solutions of diethanolamine

The absorption rates of CO₂ into aqueous solutions of Diethanolamine (DEA) with varying concentrations from 0.2 to 4M and temperature range from 293 to 323 K were measured by using a laboratory stirred reactor. The CO₂ partial pressure was varied in a range that the reaction would occur in pseudo first order regime. Experimental data were analyzed and the kinetic parameters associated with the reaction were determined. The activation energy for the deprotonation of the intermediate zwitterion was estimated at about 11.4 kcal/mol. The contribution of carbamate formation to the overall absorbed CO₂ was experimentally evaluated and found to be of the order of 100%.     

Passivity‐based sliding mode control for nonlinear systems

Passivity with sliding mode control for a class of nonlinear systems with and without unknown parameters is considered in this paper. In fact, a method for deriving a nonlinear system with external disturbances to a passive system is considered. Then a passive sliding mode control is designed corresponding to a given storage function. The passivity property guarantees the system stability while sliding mode control techniques assures the robustness of the proposed controller. When the system includes unknown parameters, an appropriate updated law is obtained so that the new transformed system is passive. The passivation property of linear systems with sliding mode is also analysed. The linear and nonlinear theories are applied to a simple pendulum model and the gravity‐flow/pipeline system, respectively. Copyright © 2008 John Wiley & Sons, Ltd.     

Comparison of copper emission rates from wood treated with different preservatives to the environment

This study describes a laboratory method for the estimation of emission from preservative-treated wood in the different situations where emissions could enter the environment for use classes 3 (not in contact with ground) and 4 and 5 (in contact with the ground, fresh water or sea water) according to OECD Guidelines. Samples of scotch pine sapwood (Pinus sylvestris L.) were treated with CCA (1% and 2%), ACQ-1900 (3% and 7%), ACQ-2200 (2%), Tanalith E 3491 (2% and 2.8%), and Wolmanit CX-8 (2%).     

A framework to integrate software behavior into dynamic probabilistic risk assessment

Software plays an increasingly important role in modern safety-critical systems. Although, research has been done to integrate software into the classical probabilistic risk assessment (PRA) framework, current PRA practice overwhelmingly neglects the contribution of software to system risk. Dynamic probabilistic risk assessment (DPRA) is considered to be the next generation of PRA techniques. DPRA is a set of methods and techniques in which simulation models that represent the behavior of the elements of a system are exercised in order to identify risks and vulnerabilities of the system. The fact remains, however, that modeling software for use in the DPRA framework is also quite complex and very little has been done to address the question directly and comprehensively. This paper develops a methodology to integrate software contributions in the DPRA environment. The framework includes a software representation, and an approach to incorporate the software representation into the DPRA environment SimPRA. The software representation is based on multi-level objects and the paper also proposes a framework to simulate the multi-level objects in the simulation-based DPRA environment. This is a new methodology to address the state explosion problem in the DPRA environment. This study is the first systematic effort to integrate software risk contributions into DPRA environments.     

Enhancement of Flexural Design of Horizontally Curved Prestressed Bridges

In this paper, flexural behavior of horizontally curved prestressed (posttensioned) box bridges is studied by using three-dimensional and refined finite-element modeling and analysis. Bridge length, section geometry, and material properties are the same in all the models, while angle of curvature varies from 0 to 90°. The results of analysis show that in curved bridges, stress distribution is significantly different in comparison to straight bridges. Also, the level of stresses at some locations of section width is considerably high. It is proposed to vary the distribution of the prestressing tendons across section width in order to optimize the bridge capacity. Results show that by proper redistribution of prestressing in section width, significant reduction in resultant stress is possible.     

Dependence on the motif YIPP for the physical association of Jak2 kinase with the intracellular carboxyl tail of the angiotensin II AT1 receptor

Angiotensin II is the effector molecule of the renin-angiotensin system. Virtually all of its biochemical actions are mediated through a single class of cell-surface receptors called AT1. These receptors contain the structural features of the seven-transmembrane, G-protein-coupled receptor superfamily. Angiotensin II, acting through the AT1 receptor, also stimulates the Jak/STAT pathway by inducing ligand-dependent Jak2 tyrosine phosphorylation and activation. Here, we show that a glutathione S-transferase fusion protein containing the carboxyl-terminal 54 amino acids of the rat AT1A receptor physically binds to Jak2 in an angiotensin II-dependent manner. Deletional analysis, using both in vitro protocols and cell transfection analysis, showed that this association is dependent on the AT1A receptor motif YIPP (amino acids 319-322). The wild-type AT1A receptor can induce Jak2 tyrosine phosphorylation. In contrast, an AT1A receptor lacking the YIPP motif is unable to induce ligand-dependent phosphorylation of Jak2. Competition experiments with synthetic peptides suggest that each of the YIPP amino acids, including tyrosine 319, is important in Jak2 binding to the AT1A receptor. The binding of the AT1A receptor to the intracellular tyrosine kinase Jak2 supports the concept that the seven-transmembrane superfamily of receptors can physically associate with enzymatically active intracellular proteins, creating a signaling complex mechanistically similar to that observed with growth factor and cytokine receptors.     

An automated coding and classification system with supporting database for effective design of manufacturing systems

The philosophy of group technology (GT) is an important concept in the design of flexible manufacturing systems and manufacturing cells. Group technology is a manufacturing philosophy that identifies similar parts and groups them into families. Beside assigning unique codes to these parts, group technology developers intend to take advantage of part similarities during design and manufacturing processes. GT is not the answer to all manufacturing problems, but it is a good management technique with which to standardize efforts and eliminate duplication. Group technology classifies parts by assigning them to different families based on their similarities in: (1) design attributes (physical shape and size), and/or (2) manufacturing attributes (processing sequence). The manufacturing industry today is process focused; departments and sub units are no longer independent but are interdependent. If the product development process is to be optimized, engineering and manufacturing cannot remain independent any more: they must be coordinated. Each sub-system is a critical component within an integrated manufacturing framework. The coding and classification system is the basis of CAPP and the functioning and reliability of CAPP depends on the robustness of the coding system. The proposed coding system is considered superior to the previously proposed coding systems, in that it has the capability to migrate into multiple manufacturing environments. This article presents the design of a coding and classification system and the supporting database for manufacturing processes based on both design and manufacturing attributes of parts. An interface with the spreadsheet will calculate the machine operation costs for various processes. This menu-driven interactive package is implemented using dBASE-IV. Part Family formation is achieved using a KAMCELL package developed in TURBO Pascal.